Chapter 3 Points to note at installation When attaching the laser scanner cover , put the shutter lever  through the hole  on the scanner cover. The engine controller controls the laser scanner unit and high-voltage power supply circuit and forms images based on the video signals on papers. Points to note at installation When attaching the terminal , make sure that the contact spring  contacts as shown. Chapter 2 CPU of engine controller determines the fixing assembly error and shuts the fixing heater drive signal FSRD and also turns OFF relays to shut the power supply to the fixing heater in the following cases. Page 18 Chapter 1 1. After the main controller receives the dot data, it creates the video data and send it to the engine controller. Chapter 4 F T Fixing inlet guide Static eliminator Transfer roller Pickup roller Separation pad Feeding roller Follow the procedure below for cleaning during servicing.
|Date Added:||13 July 2011|
|File Size:||53.88 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Картридж лазерный Cactus CS-C725
Canon i sensys lbp3010b disassembling and assembling, be careful not to loose the 2 springs  of the Pickup Tray Unit. Overview Chapter 2 8 When the Four-faced mirror rotates at a constant speed, the laser beam on the Photosensitive drum is scanned on the Photosensitive drum at a constant speed. This equipment applies DC positive bias to the transfer roller facing the photosensitive drum and charges papers positively.
Canon i sensys lbp3010b 2 The following are the blocks of print process and the steps. F Points to note at installation When attaching the terminal , make sure that the spring contact point  4 Disconnect the 4 connecters . Chapter 3 2 While releasing the 3 claws , remove the left cover  in the direction of the arrow.
In other words, the user ii free of laser-related hazards as long as the machine is being used for its intended purposes. Chapter 2 Cleaning blade Photosencitive drum Cleaner container F 2. Enter text from picture: Chapter 2 Laser beam Unexposed area Exposed area F 2. Before Removing The Sensor Pcb Chapter 3 Points to note at installation When attaching the terminal , make sure that the contact spring  contacts as shown.
Test patterns horizontal lines are output when executing this test print. The canon i sensys lbp3010b controller monitors the fixing heater temperature detection signal FSRTH and outputs the fixing heater drive signal FSRD according to canon i sensys lbp3010b detected temperature.
Как установить принтер без диска: инструкция
F F 3 Disconnect the 4 connecters  and free the harness  from the harness Chapter 3 F 6 Remove the Fixing Assembly . Page Chapter 4 F T Fixing inlet guide Static canon i sensys lbp3010b Transfer roller Pickup roller Separation cankn Feeding roller Follow the procedure below for cleaning during servicing.
Page 65 Chapter 2 2.
Generating Primary Charging Bias Chapter 2 Engine controller High-voltage power supply Primary charging high-voltage generation primary canon i sensys lbp3010b roller circuit developing cylinder Developing high-voltage generation circuit Transfer high-voltage Transfer roller generation circuit F 2.
Page 82 Chapter 3 F 2 Remove the cartridge arm . There is only a face-down delivery. Chapter 2 Engine controller High-voltage power supply Primary charging high-voltage generation primary charging roller circuit developing cylinder Developing high-voltage generation circuit Transfer high-voltage Transfer roller generation circuit Canon i sensys lbp3010b 2. Sensor Chapter 6 6. Symbols Used Introduction Symbols Used This documentation uses the following symbols to indicate special information: Fixing block Step 6: Engine Controller Board Chapter 3 F 2 Remove the terminal  and free the harness  from the harness guide .
Chapter 3 F Points to note at installation When attaching the laser scanner cover , put the shutter lever  through canon i sensys lbp3010b hole  on the scanner cover. At the time of turning on the power or closing the upper cover, the engine controller judges the position of the Toner cartridge flag based on the output sensyx of the leading edge sensor PS General Description Chapter 2 2.
canon i sensys lbp3010b
Canon LBP6000 Series Service Manual
Before Removing The Memory Contact Unit Chapter 3 Points to note at installation When attaching the laser scanner cover , put the shutter lever  through the hole  on the scanner cover. The following shows the 2 claws  at rear sejsys of the Upper Cover Unit, 6 canon i sensys lbp3010b  at the sides, and 3 hooks . Chapter 3 F 3 Remove the Tension Unit .
Chapter 2 This machine performs the throughput down control that extends the paper interval and lower the printing speed to prevent the edge of the fixing heater from over- heating at continuous printing of small paper the paper with narrow width and to prevent the fixing heater unit from overheating at high-volume continuous print- ing. Service Tools Chapter 5 5. Page 71 Chapter 2 Resolution Settings This canon i sensys lbp3010b has 2 types of resolution settings x dpi, x dpi.
Table Of Contents Contents 4. Laser beam exposure In this step, static latent images are formed on the photosensitive drum with laser canon i sensys lbp3010b.
External View Chapter 1       F  Fixing unit  Pressure roller  Delivery roller  Fixing film unit  Laser scanner unit  Manual feed tray  Pickup tray  Photosensitive drum  Pickup roller  separation pad  Feed roller  Transfer roller  Toner cartridge Reduction in standby time and energy consumption This equipment employs on-demand fixing lbp3010h the heater swnsys only during printing, resulting in a reduction in standby time and energy consumption on this mode.
canon i sensys lbp3010b
Totaalinkt – Goedkope inkt en toner cartridges, o.a. voor HP, Canon, Epson, Brother, Samsung
Toner canon i sensys lbp3010b transferred on the paper and fused by the heat of the fixing heater on the fixing assembly and by the pressure from the pressure roller, then the paper is delivered from the fixing assembly. F 2 Disconnect the 4 connectors . Chapter 3 F 2 Remove the Cartridge Arm . Page Sep 8 Fixing delivery sensor PS In the event of major changes in the contents of this manual over a long or short period, Canon will canon i sensys lbp3010b a new edition of this manual.
This fixing assembly is equipped with canon i sensys lbp3010b thermistor. Using The Machine Chapter 1 1. Omdat wij rechtstreeks inkopen bij de producent en kunnen sehsys u altijd de scherpste prijs bieden. Toner Level Detection Chapter 2 2. Page 5 Introduction The following rules apply throughout this Service Manual: Chapter 2 CPU detects residual jam when meeting the following conditions: Chapter 3 – Be sure not to touch the surface  of the Fixing Film Unit.
In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbolthe arrow indicates the direction of the electric signal.